QUICK FAQ. REQUEST US TO ADD YOUR QUESTION HERE!!!

1- How to import in Agisoft Photoscan the coordinates of photos Check the video and software of this link

How to Post Processing Kinematic (PPK) for Photogrammetry

How to Post Processing Kinematic (PPK) for Photogrammetry With RTKITE you can capture photos directly in RTK mode, so you will avoid the needed of Ground Control Points, or GCP. For this task, some li...

RTKite to Pixhawk integration guide

RTKite to Pixhawk integration guide   This quick manual with guide you to integrate North's RTKite System-on-Module GNSS RTK receiver to operate as the main GPS for 3DR's Pixhawk autopilot module. ...

RTK with ARDUPILOT over MAVLINK

You can use the telemetry of UAV (any of compatible models) for send the RTCM messages from a laptop to the RTKITE https://www.youtube.com/watch?v=4wkQepaMJVY

How to install the optional LEDS on RTKITE

How to install the optional LEDS on RTKITE Please, check link according your board version For RTKite v3 board https://www.dropbox.com/s/a39f00voym9tww5/HOW%20TO%20INSTALL%20THE%20OPTIONAL%20LEDS%20ON...

What's AutoCaster and how it works?

What's AutoCaster and how it works?AutoCaster is a web service running at this URLhttp://autocaster.ddns.netIt act as a link between a given Base (configured as Base AutoCaster) and one o more Rovers ...

How to connect MPU9250 to RTKITE

How to connect MPU9250 to RTKITE Please, check this link For the new RTKITE V3 https://www.dropbox.com/s/9fsu58bxftv0jy9/IMU-MPU9250-RTKITE-V3.pdf?dl=0 In versio

Is there any way to get the RTK Output Port (RS232) onto the same 38400 baud rate as the TTL (3.3v) RTCM port?

Is there any way to get the RTK Output Port (RS232) onto the same 38400 baud rate as the TTL (3.3v) RTCM port? If your board is "RS232 version", then Pin 2 and 3 are of this logic.If your board is "T...

Flash synchronization

Flash synchronization of photos (for avoid GCP)With this technique you will be able to synchronize the GPS and photo with a very high accuracy in time (only limited by the specs of your camera)Require...

TXT File Format

TXT File Format   This file is generated in the SD Card in all Drone modes if you press the push-button shortly (0.5 seconds). Once done the surveying, press again the push-button shortly for close th...

LOG File Format

LOG File Format   This file is generated optionally in parallel with files TXT and NOR (RAW data). For enable the generation of LOG file, set in the App the "Extra Log" to "Enabled" This file is gener...

Recommendations for RTKITE PCB handling with safety

General recommendations for all printed circuit boards (PCB)     1) Never touch any electronic part with hand or fingers. Human body have big capacitance and can discharge high voltage spikes (ES

Firmware Update RTKITE

  Firmware Update RTKITE First, be sure of what version board of RTKITE have you

What protocol and messages are supported for output from?

What protocol and messages are supported for output from?   Protocols supported are NMEA and Novatel (Binary and ASCII)The RTKITE have some predefined modes for some typical applications. They are:  

Setup a pair of RTKite for Moving Base RTK

Landing into a moving target

Landing into a moving target   My plane needs to land into a moving target, how can be it done?   F

Phase center for Helix antenna

Phase center for Helix antenna  

Antenna schemas available for RTKITE

Antenna schemas available for RTKITE    

Troubleshooting for antenna reception

Troubleshooting for antenna reception We have made an update, 1.2.1 of FW and 2.9 of App https://www.dropbox.com/s/xj6ctesa9v0q3gd/RTKite_FW_Update_1_2_1_RC2.exe?dl=0

There are any API for access the content of SD Card by cable?

You can stream the content of SD Card to the serial port so you can capture the file with your own program.You can use Bluetooth (COM Port) in the PC, then use this protocol for request the file you w...

Pulse per second signal (1PPS)

  For a basic introduction of this feature, you can see for example:   https://en.wikipedia.org/wiki/Pulse-per-second_signal  

Behaviour of the LED DL1 (COLOR RED)

Behaviour of the LED DL1 (COLOR RED) The LED DL1 (COLOR RED) shows a blinking when the RTKITE unit is doing something (so mean, "wait, I'm busy"). It have the following activity: 1 - After the 10 sec ...

Behavior of the LED DL2 (COLOR GREEN)

Behavior of the LED DL2 (COLOR GREEN) The LED DL2 (COLOR GREEN) is related to the RTK features of the RTKITE unit.It have the following activity:1- Meanwhile the unit is receiving DGNSS corrections, D...

Behavior of the LED DL3 (COLOR BLUE)

Behavior of the LED DL3 (COLOR BLUE) Note:This LED maybe not mounted by default in RTKITE unit.The LED DL3 (COLOR BLUE) is related to the GNSS "autonomous" features of the RTKITE unit.It have the foll...

Behavior of the LED DL4 (COLOR AMBER)

Behavior of the LED DL4 (COLOR AMBER) Note:This LED maybe not mounted by default in RTKITE unit.This LED is reserved for future use.

Linking "Base AutoCaster" to "Mission Planner" via COM Port

"Base AutoCaster" is a receiver mode available in RTKITE and SMARTK products.This mode will operate as Base, sending the differential corrections (RTCMv3 advised) to a Server (the "AutoCaster server")...